Навигация
 

ГЛАВНАЯ

 

FAQ

 

СПРАВОЧНИК

 

ЭНЦИКЛОПЕДИЯ

 

XEROX




Материалы сайта
 

НОВОСТИ

 

ПУБЛИКАЦИИ

Локальный форум
 

2003

 

2004

 

2005

 

2006

 

2007



Главная страница --> Архив локального форума 2006

toshib1550: c26


root
Zdravo Darko od Skopje imam problem so fotokopir toshiba 1550 javuva kod c26 lampate e ok kabelot e ok plocata za ekspozicija e ok voedno masinata imala struen udar .Hi darko from Skopje i have problem with fotocopier toshiba 1550 what is show code c26.The exposituere lamp is ok kabel for expoziture lamp is ok,the expositure board is ok,i dont now what is it if some one now i hope they gona help.The machine have power schock from thunder.
root
C26-exposure lamp detect problem

root
i now but exposure lamp ok kabel ok board for exposure ok
root

I have correctly understood? At you a mistake с26? At it the unique decision of a problem. That which I has written. More than anything
root
The device after a thunder-storm? In this case to understand with electronics, a payment. To change easier
root
г.Шахты Ростовской обл.
Не мешало бы уточнить, в какой момент аппарат выпадает в ошибку.
Если память не изменяет, С26 отслеживается датчиком. Лампа вообще, горит?
root
говорит горит

root
Азов, Ростовской обл
If the exposure lamp is light on - check exposure lamp sensor - small black box near rear side under the exposure glass near the optic cover .
How ? - To replace it.

root
yes i check the senzor is ok.when i go to 03-33 the lamp wont go on
root
г.Шахты Ростовской обл.
lamp is ok - это еще не значит, что горит.
Возможно просто задраны значения для крайних положений ручника.
root
Азов, Ростовской обл
If the lamp is go on in 03-33 - the sensor is not OK 100 %.
In 03-33 the lamp is go on is independently of the sensor....
You must to replace sensor for the checking or instal your sensor in the other copier for checking...
root
Азов, Ростовской обл
May be right....
Please check value in 05-1, install 128 (default), then perform 05-49 by the white paper and check then...

root
Азов, Ростовской обл
If the machine have power shock withe thounder please change processor board with the working and check....
This easiest way for checking...

root
i change the procesor board is ok and therefore i change the power board and the machine is ok.I check 24v is ok 5v is ok but 15v from pin 3 i dont have it


Рекомендуем:
- Lexmark OptraE+: Справа скраю бледная печать
- sharp ar m155: ошибка l1-00
- sharp al: тонер-картридж
- Сanon IP3000: Поменял головку, не идет черный цвет
- utax 218: Ошибка с500
- RISO RC6300: плёнка для ризографа
- toshib1550: c26

Panason DP-1520: барабан


root
Наш менеджер хочет заказать для клиента картридж и барабан, просит меня предоставить парт-номера. Я аппарат в глаза не видел, по характеристике в инете предполагаю, что там 2 картриджа (драм и тонер). Пожалуйста скиньте парт-номера картриджей, барабана и тонера, ну или читать далее





При перепечатке материалов ссылка на RadX.ru обязательна
Copyright © RadX.ru
^наверх
Яндекс.Метрика